part no: CC-0601 description: magnetic buzzer phone: 800.275.4899 fax: 503.612.2381 www.cui.com 20050 sw 112th ave. tualatin, or 97062 date: 8/21/2006 unit: mm page no: 1 of 4 specifications rated voltage 1.5 vo-p operating voltage 1.0 - 1.7 vo-p mean current 80 ma max. applying rated voltage, 3000 hz square wave, ? duty coil resistance 6 1 ? coil impedance 8 ? sound output min. 70 (typical 77) dba distance at 10cm (a-weight free air). applying rated voltage of 3000 hz, square wave, ? duty. rated frequency 3,000 hz operating tempurature -20 ~ +60 c storage tempurature -30 ~ +70 c dimensions ?6.6 x h3.5 mm see attached drawing weight 0.4 g material ppo (black) terminal pin type (au plating) see attached drawing rohs yes frequency response curve
part no: CC-0601 description: magnetic buzzer phone: 800.275.4899 fax: 503.612.2381 www.cui.com 20050 sw 112th ave. tualatin, or 97062 date: 8/21/2006 unit: mm page no: 2 of 4 appearance drawing measurement method tolerance: 0.5
part no: CC-0601 description: magnetic buzzer phone: 800.275.4899 fax: 503.612.2381 www.cui.com 20050 sw 112th ave. tualatin, or 97062 date: 8/21/2006 unit: mm page no: 3 of 4 mechanical characteristics item test condition solderability lead terminals are immersed in rosin for 5 seconds and then immersed in a solder bath of +270 5c for 3 1 seconds. soldering heat resistance lead terminals are immersed in solder bath of +260 5c for 3 1 seconds. terminal mechanical strength the force of 9.8 n (1.0 kg) should be applied to the terminals. vibration the buzzer will be measured after applying a vibration amplitude of 1.5 mm with 10 to 55 hz band of vibration frequency to each of the 3 perpendicular directions for 2 hours (6 hours total). drop test the part is to be dropped from a height of 75 cm onto a 40 mm thick wooden board 3 times in 3 axis (x, y, z) for a total of 9 drops. evaluation standard 90% min. of lead terminals should be covered with fresh solder. (except the edge of the terminal.) no in interference in operation. no damage or cutting off. after the test, the part should meet specifications without any damage to the appearance and the spl should be within 10 dba of the initial measurement. environment test item test condition high temp. test the part will be subjected to +70c for 96 hours. low temp. test the part will be subjected to -30c for 96 hours thermal shock the part will be subjected to 10 cycles. one cycle will consist of: temp./humidity cycle the part shall be subjected to 10 cycles. one cycle will be 24 hours and consist of: evaluation standard after the test, the part should meet specifications without any damage to the appearance or performance except spl. after 4 hours at 25c, the spl should be within 10 dba of the initial measurement.
part no: CC-0601 description: magnetic buzzer phone: 800.275.4899 fax: 503.612.2381 www.cui.com 20050 sw 112th ave. tualatin, or 97062 date: 8/21/2006 unit: mm page no: 4 of 4 reliability tests item test condition operating (life test) 1. continuous life test: the part will be subjected to 72 hours at 45c with 1.5 v, 3000 hz applied. 2. intermittent life test: a duty cycle of 1 minute on, 1 minute off, a minimum of 10,000 times at room temp. (+25 10c) with 1.5 v, 3000 hz applied. evaluation standard after the test, the part should meet specifications without any damage to the appearance or performance except spl. after 4 hours at 25c, the spl should be within 10 dba of the initial measurement. test conditions standard test condition a) tempurature: +5 ~ +35c b) humidity: 45 - 85% c) pressure: 860 - 1060 mbar judgement test condition a) tempurature: +252c b) humidity: 60 - 70% c) pressure: 860 - 1060 mbar packaging each minimum package of products will be in a carton box and it should be clearly marked with the part number, quantity, and outgoing inspection number. there should be no mechanical damage to the products during transportation and/or in storage.
|
